模數式橋梁伸縮縫

服務	基礎建筑材料	詳細地址	橡塑路
QQ號	1334576766

模數式橋梁伸縮縫

GQFC型、GQFZ型、GQFL型、GQFF型、GQFMZL型模數式橋梁伸縮裝置，是采用熱軋整體成型的異型鋼材設計的橋梁伸縮裝置。GQFC型、GQFZ型、GQFF型、GQFL型伸縮裝置適用于伸縮量80mm以下的橋梁接縫，GQFMZL型伸縮裝置是由邊梁、中梁、橫梁和連動機構組成的模數式橋梁伸縮裝置，適用于伸縮量80mm-1200mm的大中跨度橋梁。

GQF C type， GQF Z type， GQF L type， GQF F type and GQF MZL modulus bridge expansion device are bridge expansion devices designed by hot rolled integral shaped steel products. GQF - C bridge joint type， GQF - Z， GQF - F， GQF - L telescopic device is suitable for the expansion amount below 80mm， GQF - MZL type expansion device is a modular bridge expansion device is composed of edge beam， beam， beam and linkage mechanism， suitable for large and medium expansion 80mm-1200mm long span bridge.

2、設計制造技術條件

2. Technical conditions for design and manufacture

1、設計荷載：采用J刊公路工程技術標準規定的汽車超過20級荷載進行設計。

1， design load using J magazine 01 - highway engineering technical standard stipulated in the vehicle over 20 load to carry out the design.

2、本結構使用的異型鋼材質為16Mn橋梁專用鋼，鋼材抗拉強度應不低于480Mpa，容許彎曲應力不低于210Mpa。

2. The special-shaped steel material used in this structure is 16Mn bridge special steel. The tensile strength of steel should not be less than 480Mpa， and the ading stress is not less than 210Mpa.

3、結構中支承橫梁使用16Mn或45號鋼，其容許彎曲應力不低于210Mpa。

3. 16Mn or No. 45 steel is used in the supporting beam in the structure， and the ading stress is not less than 210Mpa.

4、其余配件鋼材可使用不低于Q235強度鋼材。

4， the rest of the fittings steel can be used not less than Q235 strength steel.

3、膠料適用范圍

3. The scope of application of rubber

1、采用氯丁橡膠（C日）的伸縮裝置適用于溫度為25+60地區。

1. The telescopic device used for chloroprene rubber （C day） is suitable for the temperature range of - 25 - C - +60 C.

2、采用天然橡膠（N日）的伸縮裝置適用于溫度為40+60地區。

2. The expansion device of natural rubber （N day） is suitable for the temperature range of - 40 C to +60 C.

4、結構特點

4. Structure characteristics

GQFMZL型伸縮裝置的突出特點是將伸縮裝置的承重結構和位移控制系統分開，二者受力時互不干擾，分工明確，這樣既保證受力時安全，又保證了受力時位移均勻。

The prominent feature of the GQF MZL expansion device is to separate the load bearing structure and the displacement control system of the telescopic device. The two forces are not interfered with each other， and the division of labor is clear. This ensures the safety of the force while ensuring the even displacement of the load.

5、伸縮裝置伸縮量的確定

5. Determination of expansion capacity of telescopic device

橋梁伸縮量計算值直接影響對伸縮裝置規格選擇，若伸縮裝置規格選擇不合理，就直接影響伸縮裝置的使用效果，同時選擇伸縮裝置時還應考慮梁、板間伸縮裝置間隙量大小，以保證伸縮裝置與梁、板兩端有充分錨固，才能達到佳使用效果。所以在選擇伸縮裝置的規格時，一定要留足夠余量，才能保證伸縮裝置的使用效果和耐久性。

The value of direct influence on the choice of expansion device specification calculation of bridge expansion volume， if the expansion device specification selection is not reasonable， it directly affects the use effect of expansion device at the same time， expansion device should be taken into consideration when the beam and plate expansion device gap size， to ensure the expansion device has sufficient anchorage and beam， both ends of the board， in order to achieve the best use effect. So when choosing the size of the telescopic device， we must leave enough allowance to ensure the use and durability of the telescopic device.

6、橋梁設計單位在選擇了我公司的伸縮裝置后，為便于加工制作，應提供下列資料

6， the bridge design unit should provide the following information for the convenience of processing and production after the selection of the expansion unit of our company.

1、橋梁的橫斷面圖（包括橫坡、人行道、安全帶、欄桿的位置及尺寸）o

1. The cross section of the bridge （including the horizontal slope， the sidewalk， the seat belt， the position and size of the railing） o

2、伸縮裝置的施工實施時間及安裝時溫度的變化幅度。

2. The construction time of the telescopic device and the change range of the temperature at the time of installation.

3、用戶有特殊要求應明確注明。

3， the special requirements of the user should be clearly stated.

注：如用戶不提供定位值，則工廠一律按產品的額定大伸縮量壓縮一半定位出廠。

Note if the user does not provide the positioning value， the factory will be compressed by half of the rated maximum expansion of the product.